Parr-instrument PDM Uživatelský manuál stáhnout pdf (Strana 1)

Installation Instructions for

Pressure Display Module (PDM)

556M

Meter Installation in 4848 Reactor

Controller

1. Unplug the power cord of the 4848 controller.

Remove the (2) screws located on the top/front

cover at the rear corners of the controller. Gen-

tly lift the cover forward, which is hinged at the

bottom, taking care not to apply tension on any

internal wiring.

2. If applicable, remove and discard the black hole

plug on the sloped front panel above the “PRES-

SURE” text. This can be done by pinching the

clasps on the back of the plug from the inside of

the front plate.

3. Insert the PDM (2082E) through the panel cutout,

from outside in, making sure the rubber gasket

is on the outside of the controller front panel.

(If wires are preinstalled, remove the terminal

connector by releasing the tabs on the sides of

the module and gently pulling the terminal con-

nector off. Reference photos below.) Slide the

white mounting bracket onto the module with

the mounting screws pointing towards the front

panel. Slide the mounting bracket forward until

it touches the controller panel. The clasps on the

mounting bracket should align with the groves

on the module. Gently tighten the screws until

the module is held into place. (If removed, reat-

tach the terminal connector.)

Terminal Connector Removal

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Pressure Display Module (PDM)

Installation Instructions for Pressure Display Module (PDM)556MMeter Installation in 4848 Reactor Controller1. Unplug the power cord of the 4848 cont

Strany 2 - PDM Installation

PDM InstallationParr Instrument Company2Meter Installation in 4848 Reactor Controller (Continued)Meter Installation Diagram

Strany 3

PDM Installationwww.parrinst.com37 8 9 10 11 121 2 3 4 5 62082E Pin Out(Pin 5 is blank)6. Take the black and white cable, with both ends stripped, fr

Strany 4

PDM InstallationParr Instrument Company4Wiring Installation in 4848 Reactor Controller (Continued)9. Find the free orange wire #1 from the kit and at

Strany 5

PDM Installationwww.parrinst.com5PDM Wiring Schematic2082E/1212STRIP .23BLACK#112082E/75-WHITE +STRIP .2319LOC1NO.WIRE4+BLUE13STRIP .35END#2LOCWHIT

Strany 6

PDM InstallationParr Instrument Company6A2104E Harness Wiring Schematic

Strany 7

PDM Installationwww.parrinst.com7Factory Default SettingsPressure ModuleKeys command:1. Press “SET” to select 2. Press return key move to next opera

Strany 8 - Revision 05/03/13

Revision 05/03/13

Další dokumenty pro Senzory Parr-instrument PDM

Zobrazit dokument Parr-instrument PDM Uživatelský manuál

Parr-instrument PDM Uživatelský manuál (12 stránky)

Komentáře k této Příručce

Žádné komentáře

Parr-instrument PDM Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Parr-instrument PDM. Parr Instrument PDM User Manual Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Senzory Parr-instrument PDM

Komentáře k této Příručce

Parr-instrument PDM Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Parr-instrument PDM. Parr Instrument PDM User Manual Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Senzory Parr-instrument PDM

Komentáře k této Příručce

Související produkty a manuály pro Senzory Parr-instrument PDM